Some PVT units encountered DRAM calibration failure during power on/off
tests. The failure is caused by higher impedance of the DRAM on those units.
So increase the driving strength for 4GB DRAMs.
BUG=chrome-os-partner:57392
TEST=run cold reboot 100 times on PVT units which have DRAM calibration issue.
Change-Id: I0d1776cd1a5892d1f82e9bf414620d1ef6d29132
Signed-off-by: PH Hsu <ph.hsu@mediatek.com>
Reviewed-on: https://chromium-review.googlesource.com/394451
Commit-Ready: Yidi Lin <yidi.lin@mediatek.com>
Tested-by: Yidi Lin <yidi.lin@mediatek.com>
Reviewed-by: Pin-Huan Hsu <ph.hsu@mediatek.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
We found that Kevin board PHY0 and PHY1 eye-diagram margin
is not enough to make compliance test pass, and the PHY0 USB
SI is worse than PHY1, because of the higher PCB impedance.
For PHY0, we can't improve the eye-diagram by SW PHY tuning,
so we need to reduce the RBIAS resistance from 133 ohm to 115
ohm, it can help to increase the eye-height.
For PHY1, we can improve the eye-diagram by setting the max
pre-emphasis level.
And after the above change, the USB2 signal amplitude will
become larger at the test point near to SOC USB2 PHY, in order
to avoid mis-trigger the disconnect detection (650mV), we need
to disable pre-emphasize in eop state.
BRANCH=None
BUG=chrome-os-partner:53863
TEST=do USB 2.0 compliance test for Kevin C0 and C1 port.
Change-Id: I00cb325b9938e4276cc77b5d6f5faa7023379608
Signed-off-by: William wu <wulf@rock-chips.com>
Reviewed-on: https://chromium-review.googlesource.com/390615
Commit-Ready: Julius Werner <jwerner@chromium.org>
Tested-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Though we don't use Type-C PHY to support USB3 in firmware,
we still need to initialize the Type-C PHY, and make sure
the power state of pipe is always fixed to U2/P2. After
this, we can force USB3 controller to work in USB2 only
mode stability.
BRANCH=none
BUG=chrome-os-partner:56425
TEST=Go to recovery mode, plug a Type-C USB drive containing
chrome OS image into both ports in all orientations, check if
system can boot form USB.
Change-Id: Ie3654cd1c1cb76b62aa9b247879b60cbecee0155
Signed-off-by: William wu <wulf@rock-chips.com>
Reviewed-on: https://chromium-review.googlesource.com/391412
Commit-Ready: Julius Werner <jwerner@chromium.org>
Tested-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Move the setup of the IRQ status handler so it will be set up properly
before the early probe happens.
BUG=chrome-os-partner:53336
BRANCH=None
TEST=None
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16861
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Change-Id: I4380af1233d2a252899459635a3cb69ca196088d
Reviewed-on: https://chromium-review.googlesource.com/393296
Commit-Ready: Furquan Shaikh <furquan@chromium.org>
Tested-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Due to different LCD panel requirements the delay between LVDS becomes
active and the backlight is switched on needs to be increased to 500 ms.
BUG=None
BRANCH=None
TEST=None
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/16875
Tested-by: build bot (Jenkins)
Reviewed-by: Kysti Mlkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Change-Id: I09029624469aef412141c7b46224d48557ba4af1
Reviewed-on: https://chromium-review.googlesource.com/393295
Commit-Ready: Furquan Shaikh <furquan@chromium.org>
Tested-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Internal changes:
- Fix shellcheck issues.
- Add some help text and update section header text.
- Reorder sections to try to get better estimates of what the commits
were mainly touching.
- Start making the script slightly less coreboot-centric.
- Don't print git errors.
Changes in output:
- Find new and deleted CPUs, SOCs, northbridges, southbridges, and SIOs.
- Show new users.
- Show before and after commit count for all authors.
BUG=None
BRANCH=None
TEST=None
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16848
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Change-Id: I9858436f9458b2859a91273a525901df34796df4
Reviewed-on: https://chromium-review.googlesource.com/393292
Commit-Ready: Furquan Shaikh <furquan@chromium.org>
Tested-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The datasheets on gm45: "Mobile Intel 4 Series Express Chipset Family"
mention the possibility of having 352M ram preallocated for the
integrated graphic device. This only worked fine if the amount of ram in
the system was 3GB or less. When 4G or more is installed, memory is
remapped to create a 1GB large pci mmio hole which is not enough and
creates conflicts when 352M vram is used.
This patch increases the pci mmio hole size on Lenovo x200 to allow
352M vram to work.
TEST: build and flash on target with 4GB ram or more, use nvramtool to
set gfx_uma_size to 352M and reboot.
BUG=None
BRANCH=None
TEST=None
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16831
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Change-Id: I5ab066252339ac7d85149d91b09a9eaaaab3b5b6
Reviewed-on: https://chromium-review.googlesource.com/393291
Commit-Ready: Furquan Shaikh <furquan@chromium.org>
Tested-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Kconfig symbols of type bool are ALWAYS defined, so this code was
always being included and run, which isn't what the author wanted.
Change to use IS_ENABLED(), and a regular if() instead of an #ifdef.
BUG=None
BRANCH=None
TEST=None
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16837
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Change-Id: I72623fa27e47980c602135f4b73f371c7f50139b
Reviewed-on: https://chromium-review.googlesource.com/392869
Commit-Ready: Furquan Shaikh <furquan@chromium.org>
Tested-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
- Add an exception for MAINBOARD_POWER_ON_AFTER_POWER_FAIL when checking
- With those exceptions set, we don't have anymore #define or #ifdef
warnings, so turn them to errors so no more can be pushed.
- Change the definition of an unused symbol from a warning to a note.
There are times when unused symbols are expected.
- Upgrade the warning for loading Kconfig files multiple times from
a warning to an error.
BUG=None
BRANCH=None
TEST=None
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16840
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Change-Id: I6dcb06d4f0b099d5ccaf7643e72dd790719bdf58
Reviewed-on: https://chromium-review.googlesource.com/392868
Commit-Ready: Furquan Shaikh <furquan@chromium.org>
Tested-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The type of the default value wasn't being checked to make sure that it
matched the type of the Kconfig symbol.
This makes sure that the symbol is being set to either a reasonable
looking value or to another Kconfig symbol.
BUG=None
BRANCH=None
TEST=None
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16839
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Change-Id: Ia01bd2d8b387f319d29f0a005d55cb8e20cd3853
Reviewed-on: https://chromium-review.googlesource.com/392867
Commit-Ready: Furquan Shaikh <furquan@chromium.org>
Tested-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Everybody knows WHAT they're supposed to do with options, so the text
"Pick this" or "Select to" are redundant.
BUG=None
BRANCH=None
TEST=None
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16838
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Change-Id: I327c5be755373e99ca0738593bd78e1084d4d492
Reviewed-on: https://chromium-review.googlesource.com/392866
Commit-Ready: Furquan Shaikh <furquan@chromium.org>
Tested-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Some Chrome OS ECs require a small amount of time after a SPI
transaction to reset their controllers before they can service the next
CS assertion. The kernel and depthcharge have always enforced a 200us
minimum delay for this... coreboot should've done the same.
BRANCH=gru
BUG=chrome-os-partner:58046
TEST=Booted Kevin in recovery mode, confirmed that recovery events got
logged with correct timestamps in eventlog.
Change-Id: I6a7baf7859d5d50e299495d118e7890dcaa2c1b0
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/392206
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
Kconfig hex values don't need to be in quotes, and should start with
'0x'. If the default value isn't set this way, Kconfig will add the
0x to the start, and the entry can be added unnecessarily to the
defconfig since it's "different" than what was set by the default.
A check for this has been added to the Kconfig lint tool.
BUG=None
BRANCH=None
TEST=None
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16834
Tested-by: build bot (Jenkins)
Reviewed-by: Kysti Mlkki <kyosti.malkki@gmail.com>
Change-Id: I86f37340682771700011b6285e4b4af41b7e9968
Reviewed-on: https://chromium-review.googlesource.com/391938
Commit-Ready: Furquan Shaikh <furquan@chromium.org>
Tested-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
On resume, TPM2_Starup(STATE) command needs to be sent to the TPM. This
ensures that TPM restores the state saved at last Shutdown(STATE).
Since tlcl_resume and tlcl_startup both use the same sequence for
sending startup command with different arguments, add a common function
that can be used by both.
BUG=chrome-os-partner:58043
BRANCH=None
TEST=Verified that on resume coreboot no longer complains about index
read for 0x1007. Return value is 0 as expected.
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/16832
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Change-Id: Ib8640acc9cc9cdb3ba5d40e0ccee5ca7d67fa645
Reviewed-on: https://chromium-review.googlesource.com/391937
Commit-Ready: Furquan Shaikh <furquan@chromium.org>
Tested-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Revert commit 53552cc0 (Drop SuperIO nuvoton/nct6776),
removing the code as no other mainboard uses it.
The board Intel Saddle Brook uses this device, so add the
code back with minor adaptations.
BUG=None
BRANCH=None
TEST=None
Signed-off-by: Teo Boon Tiong <boon.tiong.teo@intel.com>
Reviewed-on: https://review.coreboot.org/16519
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Change-Id: I546879285ad8336e81798d0fbdf94f72e1fa61a2
Reviewed-on: https://chromium-review.googlesource.com/391932
Commit-Ready: Furquan Shaikh <furquan@chromium.org>
Tested-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The microcode for the BSP gets loaded early from the fit table, but in
case we have newer microcode in cbfs, try to load it again from cbfs.
BUG=chrome-os-partner:53013
BRANCH=None
TEST=Boot and verify that microcode tries to load into the BSP.
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16829
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: Ifd6c78d7b0eec333b79e0fe5cb6a81981b078f5d
Reviewed-on: https://chromium-review.googlesource.com/391931
Commit-Ready: Furquan Shaikh <furquan@chromium.org>
Tested-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch increases the CPU specific passive temp. trip point
and critical temp. trip point value for DPTF policy.
BUG=chrome-os-partner:57903
BRANCH=None
TEST=Built, booted on reef and verified this passive and
critical temp. trip points with heavy workload.
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/16766
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Venkateswarlu V Vinjamuri <venkateswarlu.v.vinjamuri@intel.com>
Change-Id: I2a38d01a6539c1bd478f8716c4b543ebcd1f2080
Reviewed-on: https://chromium-review.googlesource.com/391926
Commit-Ready: Furquan Shaikh <furquan@chromium.org>
Tested-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
For all mainboard variants use the "Google_Reef" family by default
which is populated in SMBIOS tables. A variant can provide their own
value if needed, but "Google_Reef" can reside as the family without
having to add conditions for each variant when MAINBOARD_FAMILY
have to be overridden.
BUG=chrome-os-partner:56677
BRANCH=None
TEST=None
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16813
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Change-Id: Ic214eae1e6473b32f4cb442c09c34355357e1257
Reviewed-on: https://chromium-review.googlesource.com/391805
Commit-Ready: Furquan Shaikh <furquan@chromium.org>
Tested-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
