Revision: linuxbios@linuxbios.org--devel/freebios--devel--2.0--patch-40

Creator:  Li-Ta Lo <ollie@lanl.gov>

ibm e325 

Bring imb e325 to post device object model era


git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1956 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1

src/mainboard/ibm/e325/auto.c

@@ -158,16 +158,21 @@ static void main(unsigned long bist)
 	};
 
 	int needs_reset;
+        unsigned nodeid;
+
 	if (bist == 0) {
 		/* Skip this if there was a built in self test failure */
 		amd_early_mtrr_init();
 		enable_lapic();
 		init_timer();
+
+                nodeid = lapicid() & 0xf;
+
 		/* Has this cpu already booted? */
-		if (cpu_init_detected()) {
+		if (cpu_init_detected(nodeid)) {
 			asm volatile ("jmp __cpu_reset");
 		}
-		distinguish_cpu_resets();
+		distinguish_cpu_resets(nodeid);
 		if (!boot_cpu()) {
 			stop_this_cpu();
 		}

src/mainboard/ibm/e325/failover.c

@@ -13,11 +13,14 @@
 
 static unsigned long main(unsigned long bist)
 {
+        unsigned nodeid;
 	/* Make cerain my local apic is useable */
 	enable_lapic();
 
+        nodeid = lapicid() & 0xf;
+
 	/* Is this a cpu only reset? */
-	if (cpu_init_detected()) {
+	if (cpu_init_detected(nodeid)) {
 		if (last_boot_normal()) {
 			goto normal_image;
 		} else {

targets/ibm/e325/Config.lb

@@ -1,87 +1,9 @@
 # the IBM E325
 # This will make a target directory of ./e325
 
-loadoptions
-
 target e325
 
-uses ARCH
+mainboard ibm/e325
-uses CONFIG_COMPRESS
-uses CONFIG_IOAPIC
-uses CONFIG_ROM_STREAM
-uses CONFIG_ROM_STREAM_START
-uses CONFIG_SERIAL_POST
-uses NO_POST
-uses CONFIG_UDELAY_TSC
-uses CPU_FIXUP
-uses FALLBACK_SIZE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_MP_TABLE
-uses HAVE_PIRQ_TABLE
-uses HAVE_HARD_RESET
-uses i586
-uses i686
-uses INTEL_PPRO_MTRR
-uses HEAP_SIZE
-uses IRQ_SLOT_COUNT
-uses k7
-uses k8
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses CONFIG_SMP
-uses CONFIG_MAX_CPUS
-uses MEMORY_HOLE
-uses PAYLOAD_SIZE
-uses _RAMBASE
-uses _ROMBASE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_OFFSET
-uses ROM_SECTION_SIZE
-uses ROM_SIZE
-uses STACK_SIZE
-uses USE_FALLBACK_IMAGE
-uses USE_OPTION_TABLE
-uses HAVE_OPTION_TABLE
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses  DEFAULT_CONSOLE_LOGLEVEL
-uses  CONFIG_CONSOLE_SERIAL8250
-uses MAINBOARD
-uses CONFIG_CHIP_CONFIGURE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses LINUXBIOS_EXTRA_VERSION
-
-option CONFIG_CHIP_CONFIGURE=1
-
-option  MAXIMUM_CONSOLE_LOGLEVEL=9
-option  DEFAULT_CONSOLE_LOGLEVEL=9
-option  CONFIG_CONSOLE_SERIAL8250=1
-option  CONFIG_SERIAL_POST=1
-option  NO_POST=0
-
-option CPU_FIXUP=1
-option CONFIG_UDELAY_TSC=0
-option i686=1
-option i586=1
-option INTEL_PPRO_MTRR=1
-option k7=1
-option k8=1
-
-option ROM_SIZE=1048576
-
-
-option HAVE_OPTION_TABLE=1
-option CONFIG_ROM_STREAM=1
-option HAVE_FALLBACK_BOOT=1
-
-###
-### Compute the location and size of where this firmware image
-### (linuxBIOS plus bootloader) will live in the boot rom chip.
-###
-option FALLBACK_SIZE=131072
-
-## LinuxBIOS C code runs at this location in RAM
-option _RAMBASE=0x00004000
 
 #
 ###
@@ -95,16 +17,16 @@ romimage "normal"
 	option USE_FALLBACK_IMAGE=0
 	option ROM_IMAGE_SIZE=0x10000
 	option LINUXBIOS_EXTRA_VERSION=".0Normal"
-	mainboard ibm/e325
+#	payload ../../filo.elf
-	payload ../../filo.elf
+        payload /home/ollie/work/filo-0.4.1/filo.elf
 end
 
 romimage "fallback" 
 	option USE_FALLBACK_IMAGE=1
 	option ROM_IMAGE_SIZE=0x10000
 	option LINUXBIOS_EXTRA_VERSION=".0Fallback"
-	mainboard ibm/e325
+#	payload ../../filo.elf
-	payload ../../filo.elf
+        payload /home/ollie/work/filo-0.4.1/filo.elf
 # use this to test a build if you don't have the etherboot
 #	payload /etc/hosts
 end